Fender vibro champ silverface dating
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL. If you have a cherished octal power tube or rectifier with a broken keyway, here is a great solution. STYLE MICALEX TUBE SOCKET FOR MINIATURE 9-PIN TUBES. Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 60 years of experience in producing some of the finest capacitors available today.
Perfect for Twin Reverb, Showman and Dual Showman, Quad Reverb, Bassman 100, etc. CAPACITOR, F&T BRAND, AXIAL LEAD ELECTROLYTIC, VARIOUS VALUES AND VOLTAGES AVAILABLE (SEE OPTIONS) Made in Germany.
Bolts screw into a captive nut on the top rail of the chassis, so there are no bottom nuts on these models.
Fender started using these in the very late 70s coincident with the introduction of the "Ultralinear 70 Watt and 135 Watt models" Check your amp for compatibility.
Rated 85 degrees C, -10%/ 50% number 125C3A & 022707. Vacuum impregnated with polyurethane varnish for quiet and long life operation. Typically found on the back panel of some Fender Blonde/Brown era amps, and some Blackface vintage amps. Larger than the CW-401-4 - Fender was not consistent in which washers they used on back panels over the years. Larger than the CW-401-4 / CW-401-8 sets - Fender was not consistent in which washers they used on back panels over the years. Ground Connection Terminals - Flat Used to connect a ground wire to a screw and nut on a chassis. With built-in lock washer to keep the screw and nut from loosening. DSP, Acoustasonic 30, Acoustasonic SFX II, Bassman 25, Bassman 60, Jazzmaster Ultralight Enclosure, Princeton 650, Cyber Champ, Rumble 112, Rumble 2x8, Super-Sonic 100 Head, Super-Sonic Twin, Super Champ X2/XD, and Bullet 15 DSP amplifier. Perfect for restoring that vintage amp in your closet!
For dimensions and technical specifications, click number 125C1A & 022699. Vacuum impregnated with polyurethane varnish for quiet and long life operation. OUTSIDE EDGE OF WASHER IS BARELY LARGER THAN THE HEAD OF THE Fender BACK PANEL SCREWS. handle strap, replacement for Fender "tweed" style amps (as well as other vintage amps.
Used on the upper left corner of the grill cloth on some recent and vintage era Fender amps. 5 1/2" wide, the "F" in the logo is about 2 7/8" inches tall. "Flat" Fender logo, with brown "tail", cast metal, mounting screws included.
Screw spacing is 4 inches center-to-center, strap length is 4 5/8" end-to-end.
Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes. Values available include 10u F/450V, 16u F/450V, 22u F/500V, 25u F/25V, 33u F/450V, 47u F/500V, 50u F/100V, 70u F/350V, 100u F/350V, and 220u F/350V. Chrome metal caps - replacement for vintage and reissue Fender amps. Has slight "raised" bump near the center of the handle. 6.5 inches from mounting center to mounting center.
Choose capacitor value under the Select Option box. Comes complete with two nickel-plated handle mounts and four screws.
Does NOT contain the "Made in USA" script found on some Fender logos. New original Fender reproduction, used in many recent and current model Fenders.
Used on the upper left corner of the grill cloth on most CBS era Fender amps. 4 1/2" wide, the "F" in the logo is about 2 1/2" inches tall. "Flat" Fender logo, with black "tail", cast metal, mounting screws included. New original Fender reproduction, used in many recent and current model Fenders.